Subrata Kumar Padhana,
Vipin Kumar Mishrab,
Narayan Murmua,
Sabyashachi Mishra*b and
Satya Narayan Sahu*a
aSchool of Chemistry, Sambalpur University, Jyoti Vihar, Burla-768 019, Odisha, India. E-mail: snsahu.chem@gmail.com; snsahu@suniv.ac.in
bDepartment of Chemistry, Indian Institute of Technology, Kharagpur – 721302, India. E-mail: mishra@chem.iitkgp.ac.in
First published on 30th July 2020
The detection of fluoride ions in a competitive environment often poses several challenges. In this work, we have designed and synthesized a coumarin functionalized fluorescein dyad (R3) which represents an ideal through bond energy transfer (TBET) fluorophore with the coumarin unit as donor and fluorescein unit as acceptor. The bichromophoric dyad demonstrates the detection of fluoride ions in the parts per billion (ppb) concentration level (22.8 ppb) with high selectivity via a TBET emission signal at 548 nm with a diagnostic bright yellow colour fluorescence output. Based on UV-visible, fluorescence, 1H NMR and DFT studies, it is shown that the fluoride ion induces the opening of the spirolactam ring of the fluorescein moiety and provides a π-conjugation link between the donor and acceptor units enabling a TBET phenomenon with a larger pseudo-Stokes shift of 172 nm. To the best of our knowledge, this is the first report where the fluoride ion is detected via a TBET signal between the coumarin and fluorescein units in a bichromophoric dyad.
Among the various detection techniques, the fluorescence based approach is considered as one of the preferred methods because of its simplicity and high sensitivity which translates each molecular event into a distinct fluorescence output.10–12 Several fluorescence based approaches, such as, photoinduced electron transfer (PET),13 intramolecular charge transfer (ICT)14 and excited state intramolecular proton transfer (ESIPT)15–18 have been designed for detection of fluoride ions. However, these techniques suffer a serious drawback on the loss of fluorescence intensity of the output signal as the photophysical processes in the excited state and the fluorescence emission originates from a single fluorophore. Consequently, resonance energy transfer (RET) or electronic energy transfer (EET) phenomenon comes out as a successful technique where a molecule absorbs light at the donor wavelength and emits at a wavelength characteristic of the acceptor unit.19–21 Further, this technique offers significant advantages over the other fluorescence based approaches on the basis of long wavelength emission band with large pseudo-Stokes shift and a fluorescence turn-on mode.22 Thus, various scientific groups at the present time are taking a keen interest in the construction of donor–acceptor energy transfer cassettes.23
In principle, the mechanism of energy transfer between two chromophoric moieties (donor to acceptor) can take place either through space or through conjugated bonds. Accordingly, it generates two processes such as, fluorescence resonance energy transfer (FRET) and through bond energy transfer (TBET), where the excited state energy transfer occurs through space and through bond, respectively.24 However, the design of a FRET system often requires a meticulous selection of a suitable combination of donor and acceptor moieties which are attached via a flexible non-conjugated linker with a prerequisite that the donor emission must overlap considerably with the acceptor absorption band to observe an energy transfer signal within a spatial distance of 10–100 Å.25 In contrast, a TBET system can be achieved with a large variety of donor and acceptor combinations which can be linked electronically but nonplanarly via rigid conjugated bonds that facilitate the energy transfer from donor to acceptor unit without or with a minimum spectral overlap between the donor emission and acceptor absorption bands.26 Thus, developing a TBET based receptor carries significant advantages over FRET based receptors in terms of its higher energy transfer efficiency and larger pseudo-Stokes shift.23 Among the various chromophoric groups, coumarin and fluorescein derivatives have been extensively employed to design fluorescent probes due to their higher molar absorptivity and quantum yield.27–29 Although a number of articles have been published on the fluorogenic detection of fluoride ions,30,31 to the best of our knowledge no report is available for fluoride sensing based on a TBET system. Therefore, it is envisaged that, suitable mounting of a coumarin and fluorescein unit on a single molecular framework could lead to a donor–acceptor system that can detect fluoride ions via TBET process.
With this vision, and in continuation to our efforts on the development of chromofluorogenic fluoride ion sensors,32,33 we have designed and synthesized a coumarin functionalized fluorescein dyad (R3) in the present work. The bichromophoric dyad exhibits a highly selective sensing of fluoride ions amongst the other tested anions via TBET mechanism. The fluoride ion induces the opening of the spirolactam ring of the fluorescein moiety and thereby provides a π-conjugation link between the donor coumarin and the acceptor fluorescein, which subsequently exhibits the TBET phenomenon with a much larger pseudo-Stokes shift of 172 nm. Further, the dyad shows a stronger binding constant and ppb level of sensitivity toward fluoride ion. We believe that, this is the first report where fluoride induced-TBET signal is observed between coumarin and fluorescein units in a bichromophoric dyad system.
Further, in order to check the interaction of fluoride ions individually with the coumarin and fluorescein components, UV-visible spectra were recorded by adding excess fluoride ions (10 equiv.) to a solution of coumarin hydrazide (1) and fluorescein hydrazide (2) in acetonitrile medium (10 μM). It was observed that both the components 1 and 2 independently exhibited absorption band at 388 and 515 nm respectively upon interaction with fluoride ions (Fig. S5b†), which is very close to the absorption bands at 375 nm and 524 nm of R3 in presence of fluoride ions (Fig. S5a†). This clearly indicates that both coumarin and fluorescein units in R3 are interacting with fluoride ions. However the molar absorption coefficient (ε) of 1 (ε388 = 21400) is higher than that of 2 (ε515 = 1200) in the presence of fluoride ion.
On the other hand, in case of dyad R3, addition of fluoride ions exhibited an absorption spectrum comprising of both 1 and 2 components at 375 nm and 524 nm respectively with a higher molar absorption coefficient (ε524 = 52700) value for fluorescein band in comparison to coumarin band (Fig. S5a†). This implies that a significant electronic interaction is operating between the coumarin and fluorescein (ring opened form) units in the ground state of R3 by means of synergetic effect via π-conjugation. Consequently, the dyad can be employed for colorimetric sensing of fluoride ions with high selectivity (Fig. 1b).
In fluorescence study, the dyad R3 shows a very weak emission band at 498 nm upon excitation between 325 to 400 nm which can be assigned to the signal of the coumarin moiety (inset of Fig. 2a). The possibility of electron transfer in the excited state (PET) from imino nitrogen to the coumarin fluorophore could be the reason behind the weak emissive nature of R3.27,28 However, gradual addition of fluoride ions (0–5 equiv.) to the dyad solution (10 μM) resulted in emergence of an emission band at 548 nm upon excitation at 376 nm (Fig. 2a) with a pseudo-Stokes shift of 172 nm. Consequently, it turns on a diagnostic bright yellow fluorescence signal in the solution of R3 in presence of fluoride ions under the UV-light at 365 nm (inset of Fig. 2b). This increase in the yellow fluorescence signal at 548 nm can be attributed to the opening of the spirolactam ring of fluorescein (amide form) on exposure to fluoride ions. On the other hand, when fluorescence studies were carried out by taking an equimolar mixture of coumarin component 1 and fluorescein component 2 with excess of fluoride ions (10 equiv.) in acetonitrile medium, a weak emission band at 500 nm with a shoulder at around 460 nm is appeared upon excitation on the coumarin absorption band at 376 nm (Fig. S6†).
Moreover, the fluorescence enhancement factor (I/I0) of dyad R3, fluorescein component 2 (ring opened amide form) and equimolar coumarin–fluorescein pair (1 + 2) in presence of fluoride ions are 130, 19 and 29-fold respectively when excited at 376 nm (inset of Fig. S6†). This strongly indicates that a very fast intramolecular energy transfer is operating in dyad R3 where coumarin unit performs the role of a donor while the ring opened form of fluorescein acts as the acceptor unit resulting in a TBET signal in the presence of fluoride ions. In contrast, there is a weak intermolecular energy transfer possibly exists between the donor coumarin and acceptor fluorescein (amide form) in the equimolar donor–acceptor mixed solution. This result evidently supports that fluoride interaction with R3 opens the spirolactam ring of the fluorescein unit that creates a π-conjugated linkage with the donor coumarin moiety to facilitate a strong TBET event.
The fluorescence titration experiment of R3 with various equivalents of fluoride ion shows a gradual increase in emission intensity at 450 nm upto the addition of one equivalent (Fig. 2 and inset of Fig. S7a†). On further addition of fluoride ions, the intensity of the emission band at 450 nm increases along with the TBET emission band at 548 nm. However, the intensity of 450 nm band got saturated at two equivalents of fluoride ions. Based on the titration profile (Fig. S7a†), a proposed binding mode of fluoride ions with R3 is presented in Scheme 2.
Scheme 2 A proposed binding mode and deprotonation of R3 in the presence of fluoride ions and the resultant TBET phenomenon. |
On comprehensive analysis of the profile, it is very clear that the initial addition of fluoride ions (upto one equivalent) interact with the coumarin-hydroxyl group of dyad R3 resulting in a single emission signal at 450 nm for the species A (Scheme 2). Addition of more than one equivalent of fluoride ions (upto two equivalents) could lead to the formation of species like D and E via the intermediate C (Scheme 2 and Fig. S7a†), which is evident by the appearance of two emission bands at 450 nm and 548 nm. Beyond the addition of two equivalents fluoride ion, the band at 450 nm exhibited a fall in intensity while the intensity of TBET emission band at 548 nm continued to increase till four equivalents and finally get saturated (inset of Fig. S7a†). When we observe the trail of the TBET signal at 548 nm through a ratiometric plot (I548/I450) with different equivalents of fluoride ions (Fig. S7b†), it clearly demonstrates that, below one equivalent, the anion preferentially interacts with the coumarin hydroxyl group while up to two equivalents, the formation of equilibrated species D and E via C is taking place. After two equivalents, a complete TBET signal is generated on subsequent addition of fluoride ions due to the formation of a π-conjugated species P which is fully accomplished beyond four equivalents. This observation strongly implies a stepwise interaction of fluoride ions with the dyad molecule at the two binding sites (one at coumarin hydroxyl and other at fluorescein hydroxyl groups) resulting in an overall TBET signal as shown in Scheme 2. Moreover the fluorescence enhancement factor of R3 is greater than the other reported fluorescence sensors for fluoride ions7,34 and the pseudo-Stokes shift observed in R3 in the presence of fluoride ion is much higher than the recently reported FRET based-fluoride ion sensor.35 Besides, the fluoride ion induced fluorescence colour of dyad R3 is much brighter and appears at higher wavelength region than the sole fluorescein acceptor (2 in ring opened amide form) when observed under the UV lamp at 365 nm (inset of Fig. S6†). This indicates that the TBET signal of R3 is much stronger than that of fluorescein acceptor signal without the coumarin donor when excited at the donor wavelength. Thus, the dyad can act as an excellent TBET-based sensor for detection of fluoride ions.
We have further examined the fluorescence response of R3 with other anionic species such as Cl−, Br−, I−, H2PO4−, HSO4−, AcO−, CN− and S2− ion. Addition of other anions to R3 did not show any significant change in its emission signal thereby indicating a highly selective behavior of the dyad toward fluoride ions (Fig. 3). The competitive experiments of R3 with fluoride ion (10 equiv.) in the presence of other anions (10 equiv. each) showed no substantial variation in the fluorescence intensity of the R3–F− complex. This demonstrates the practical applicability of R3 toward detection of fluoride ions along with other interfering species (Fig. 3a and b). The binding behavior of R3 with fluoride ion is quantitatively analyzed by Job's plot which exhibited a maximum optical response at 0.33 mole fraction of the dyad to indicate a 1:2 stoichiometry between R3 and F− ions (Fig. S8†). The nonlinear fit of the measured absorbance at 524 nm versus various concentration of F− ions in R3 revealed a sigmoid relationship with a correlation (R2) of 0.995 (inset of Fig. 1). The very high association constant (Ka) for R3 (5.6 × 105 M−1) indicated a higher binding affinity of this dyad toward F− ions. Further, the binding constant for R3 (Ka = 6.56 × 105 M−1) evaluated from fluorescence titration data (Fig. 2b) are well in line with those measured from UV-visible experiments. The dyad R3 shows a limit of detection (LOD) of 2.6 μM (49.4 ppb) and 1.2 μM (22.8 ppb) by UV-visible and fluorescence experiments, respectively (Fig. S9†) which indicates a high level of sensitivity of the dyad toward F− ion.
Fig. 4 1H NMR titration spectra of dyad R3 (5.0 mM) upon addition of various equivalents of F− ion in DMSO-d6. |
Analysis of the NMR titration experiment indicates that the dyad forms a hydrogen bond adduct within one equivalent of fluoride ion as evident by the broadening of –OH signals at δ 11.57 and 10.05 ppm. Subsequent addition of fluoride ions caused complete disappearance of the –OH signals due to deprotonation which was confirmed by the appearance of a triplet at around δ 16 ppm, a signature signal for the formation of HF2− species on deprotonation as depicted in Scheme 2. This process of hydrogen bond formation of R3 at lower equivalents of fluoride ion followed by deprotonation at higher equivalents was further established by the gradual upfield shifts of the signals corresponding to azomethene proton (–CHN–) H10, coumarin protons (H11 and H12) and aromatic protons (H3 and H5) of the fluorescein unit arising due to increase of intramolecular charge transfer within the dyad. These observations suggest that, R3 forms 1:1 hydrogen bonded complex with F− ion upto one equivalent as indicated in structure A and B (Scheme 2) which cause a minimal change in its optical properties. However, upto two equivalents of fluoride ions, R3 forms either a 1:2 (R3:fluoride) hydrogen-bond adduct C or partial deprotonated species like D or E as depicted in Scheme 2. Beyond four equivalents of fluoride ions, the dyad undergoes deprotonation of –OH protons forming the π-conjugated product P (Scheme 2) which strongly facilitates the TBET process.
Fig. 5 The shape and energy of the HOMO and LUMO of dyad R3, intermediates (A, B, C, D and E) and product P calculated with DFT (CAM-B3LYP)/6–311++G(d,p) method (in acetonitrile solvent phase). |
With reference to the energy (in kcal mol−1) of the free dyad R3, the optimized energy of the intermediates A (−19.0), B (−16.1), C (−33.9), D (−26.6), E (−4.3) and the product P (−25.9) were found to be lower, which signifies a better stability of the intermediates and product (Fig. S10 and Table S1†). The HOMO energy levels of the fluoride complexes are found to be higher than that of the free dyad molecule (Fig. 5) which can be attributed to the stabilizing interaction of the electron in the dyad R3 where the HOMO is delocalized over the entire molecule, thus providing lower orbital energy. In contrast, the calculated HOMO and LUMO energy gap (in eV) of the dyad is larger than that of the intermediates (A, B, C, D and E) and the product P (Fig. 5), which corroborates the red shifts observed in the UV-visible spectra of R3 upon the addition of F− ions.
Moreover, upon comparison of the relative energy of two types of 1:1 fluoride complexes A and B (Scheme 2) with respect to free dyad R3, it is interesting to note that the species A is more stable than B (Table S1†). Similarly, addition of second equivalent of fluoride ion to R3 resulting in a 1:2 fluoride complex C more preferably over the partial deprotonated species D and E due to its greater stability over the intermediates D and E (Table S1†). These results clearly imply that the hydrogen bonded adducts A, B and C are formed when the dyad R3 interacts with fluoride ions up to two equivalents. On the other hand, it leads to a completely deprotonated species P through the intermediate D beyond four equivalents of fluoride ions, as proposed in Scheme 2.
Based on the DFT studies and relative energy calculations, we have proposed a stepwise route of fluoride interaction with dyad R3 as per Scheme 2. This route starts with the formation of an intermediate A initially with one equivalent of fluoride ion followed by intermediate C with two equivalents. Addition of fluoride ions beyond two equivalents leads to the formation of partial deprotonated intermediate D (more preferably over E) that subsequently generates the product P after four equivalents of fluoride ions. This putative route is also in concordance with the fluorescence studies and 1H NMR experiments. For instance, one equivalent of fluoride ion preferably binds to the hydroxyl group of the coumarin donor which exhibits an emission signal at 450 nm and beyond that the second equivalent of fluoride ion binds to the hydroxyl group of fluorescein unit giving rise to fluorescence output at 548 nm. On further addition of fluoride ions (beyond 4 equiv.), there is formation of a π-conjugated species P which represents a perfect donor–acceptor pair to facilitate the through bond energy transfer as observed in the DFT studies (Fig. 6).
The electronic absorption and emission processes were further investigated by using time-dependent density functional theory (TD-DFT) calculations for the dyad R3 and the product P. The calculated absorption bands, the corresponding oscillator strength (f), as well as the electronic transitions responsible for the absorption bands are summarized in Table S2.† The TD-DFT calculations predict absorption bands between 280–297 nm and 326–491 nm, for R3 and product P (Scheme 2), respectively. The molecular orbitals corresponding to these states (for R3 and product P) are shown in Fig. S11 and S12.† In case of product P, after photo-absorption, the system eventually relaxes to the equilibrium geometry of S1 state from which the emission occurs to S0 state. The S1–S0 emission is calculated to occur at 492 nm, which is in a qualitative agreement with the emission band observed in the experiment (548 nm). The electronic transition responsible for this emission band clearly shows that the emission band is associated with the electronic transition from the coumarin donor to the fluorescein acceptor of the product P (Fig. 6).
Footnote |
† Electronic supplementary information (ESI) available. See DOI: 10.1039/d0ra05357k |
This journal is © The Royal Society of Chemistry 2020 |